Easy Stereo Recording, Fantastic Natural Sound!

Sound so natural, you'll think you're in the same room! The Audio-Technica AT4050ST gets raves for its undeniably natural, wide-open sound. This is the kind of honest microphone every studio needs. But don't, for a second, think this is your typical condenser mic. The AT4050ST, in fact, is a stereo condenser, ready to capture a fantastic stereo image for you, and work its way into your creative miking adventures. It has a mid-side arrangement built right in (independent cardioid and figure-8 condenser elements). So you can adjust the left and right stereo signals later to really get the sound you're after. What a mic!

Audio-Technica AT4050ST Stereo Condenser Microphone Features at a Glance:

• Independent cardioid and figure-of-eight condenser elements
  
• Switch selection of Mid-Side mode and two internally matrixed stereo modes
  
• Dual-diaphragm capsules maintain precise polar pattern definition across the full frequency range of the microphone
  
• Transformerless circuitry virtually eliminates low-frequency distortion and provides superior correlation of high-speed transients
  
• The 2-micron-thick, vapor-deposited gold diaphragms undergo a five-step aging process so that the optimum characteristics remain constant over years of use
  
• Open acoustical environment of the symmetrical housing assembly minimizes unwanted internal reflections
  
• Integral 80Hz low-cut filter switch and 10dB pad switch
  
• State-of-the-art design and manufacturing techniques ensure compliance with A-T's stringent consistency and reliability standards
  
• Custom shock mount provides superior isolation
  
• Integral 80Hz high-pass filter switch and 10dB pad switch
  
• Element: Externally polarized (DC bias) condenser
  
• Polar patterns:Cardioid, figure-8
  
• Frequency response: 20Hz-18kHz
  
• Low-frequency roll-off: 80Hz, 12dB/octave
  
• Open circuit sensitivity: Stereo 90: -42dB (7.9 mV)dB re 1V at 1 Pa; Stereo 127: -41dB (8.9 mV)dB re 1V at 1 Pa; Mid: -36dB (15.8 mV)dB re 1V at 1 Pa ; Side: -36dB (15.8 mV)dB re 1V at 1 Pa
  
• Impedance: 50 ohms
  
• Max input sound level: 149dB SPL, 1kHz at 1% T.H.D.; 159dB SPL, with 10dB pad (nominal)
  
• Noise: Stereo 90 - 25dB SPL; Stereo 127 - 16dB SPL; Mid - 15dB SPL; Side - 17dB SPL
  
• Dynamic range (typical): Mid - 134dB, 1kHz at Max SPL; Side - 132dB, 1kHz at Max SPL
  
• Signal-to-noise ratio: Stereo 90 - 69dB, 1kHz at 1 Pa; Stereo 127: 78dB, 1kHz at 1 Pa; Mid: 79dB, 1kHz at 1 Pa; Side: 77dB, 1kHz at 1 Pa
  
• Phantom power requirements:48V DC, 3.4 mA typical
  
• Switches: 90, 127, M-S; Flat, roll-off; 10dB pad (nominal)
  
• Weight: 18.2 oz.
  
• Dimensions: 7.60" length; 2.10" maximum body diameter
  
• Output connectors: Integral 5-pin XLRM-type
  
• Cable: 5.0 m (16.5') long, 8-conductor, shielded, vinyl-jacketed stereo cable with 5-pin XLRF-type connector at microphone end and two 3-pin XLRM-type connectors at output end
  
• Included accessories: AT8449 shock mount for 5/8"-27 threaded stands; 5/8"-27 threaded adapter; microphone dust cover; protective carrying case

Audio-Technica AT4050ST Specs: Microphone Type Condenser Mono/Stereo Mid-Side, 90º, 127º Polar Pattern Cardioid, Figure-8 Frequency Response 20Hz-18kHz Max SPL Mid and Side: 149dB SPL (1kHz at 1% THD); 159dB w/Pad Output Impedance 50 ohms Signal to Noise Ratio 90°: 69dB, 127°: 78dB, Mid: 79dB, Side: 77dB (All: 1kHz at 1 Pa) Self Noise 90°: 25dB , 127°: 16dB , Mid: 15dB , Side: 17dB Low Cut Filter 80Hz, -12dB/octave Pads -10dB Color Black Connector 5-Pin XLR Weight 1.34 lbs. Included Accessories Shock mount, Dust cover, Breakout cable